Ping My Network

Posted : admin On 1/26/2022
  1. Ping My Network
  2. Ping My Network Connection
  3. Ping My Wireless Network
  4. Yahoo Ping Test

This example reports whether or not the server can be pinged by determining whether the Ping method returns True. If My.Computer.Network.Ping('198.01.01.01') Then MsgBox('Server pinged successfully.' ) Else MsgBox('Ping request timed out.' ) End If Replace '198.01.01.01' with the IP address, URL, or computer name of the server to ping. Ping my network – not going home before no request time out The New UMoMA Opens its Doors The premier destination for modern art in Northern Sweden. Open from 10 AM to 6 PM every day during the summer months. The ping command is a Command Prompt command used to test the ability of the source computer to reach a specified network destination. The ping command is usually used as a simple way verify that a computer can communicate over the network with the printer. Need to know if a website or server can be reached over the internet? Use our free remote pingtool to instantly ping your serverfrom outside your network. The ping will provide full ICMP diagnosticsshowing the ping and echo reply for each ICMP packet - originating from 172.104.20.135 (Texas, USA).

Press 'Enter' to ping the devices on your network. Filter the results to print only the devices that respond to a ping by piping the results into the FIND command. For example, type.

Why ?

In case of micro-break of your Internet connection, to play online (…) the stability and the quality of your connection is important.

Using this website

This website allows you to test the stability of your internet connection without having any application to install and without having a headache :)

Using the ping command

The ping command is available on all operating systems (Window, Linux …), but on some smartphones you will probably need to download a third-party application.

Reliability of this tool?

Although this tool is reliable, the ping time measurement is indicative and not as accurate as the ping command. This is due to the fact that the tool uses the HTTP protocol(S).

The ping command is one of the most often used networking utilities for troubleshooting network problems.

You can use the ping command to test the availability of a networking device (usually a computer) on a network.

When you ping a device you send that device a short message, which it then sends back (the echo).

If you receive a reply then the device is working OK , if you don’t then:

  • The device is faulty, disconnected, switched off, incorrectly configured
  • Your network or the device you are working on is not working properly.

Note: In this tutorial we will use the ping command on Windows but it works the same on Linux

Ping Command Prompt

Ping My Network

To use the ping command you go to the command line.

On Windows (XP,7) – Start Menu>Run and enter cmd to open a command prompt.

On Windows 10 type cmd into the search box and select the cmd prompt from the displayed programs.

Ping My Network

You can use the ping cmd with an IP address or the computer/host name.

To ping an IP address go to a cmd prompt and enter:

Ping IP Address e.g. ping 192.169.0.1 or to ping a computer name:

ping computer name e.g. ping Computer1

The screen shot below shows how to use the command with an IP address.

I have shown both a failed ping (192.168.0.1), and a successful ping (192.168.1.1)

Note: a failed ping results in a request timed out response, and a success results in the reply from message with the round trip delay in milliseconds.

The screen shot below shows how to use the ping command with the computer name.

Although this is easier to use a computer name than the IP address, it is only good if it works..

If it fails it is not conclusive as there is an extra stage called name resolution involved, and that could be at fault.

Here is a quick video that takes you through the process.

Using Ping To Troubleshoot Home Network Problems

The most common use of the ping command is to troubleshoot and locate network connectivity problems.

The general idea is to ping each network interface between your machine and the destination machine.

When a ping fails it indicates a problem with that network segment.

To illustrate I have drawn a simple home network with a workstation and server separated by a router (home router/hub).

If the problem was that the workstation (WS1) cannot connect to the server, then the general procedure would be: On WS1

  1. Ping loop back address 127.0.0.1 — tests own protocol stack.
  2. Ping IP2
  3. Ping IP3
  4. Ping IP4

If all pings work except the IP4 ping then we know that there is a problem on the network between the router and server.

Ping My Network

The Ping Command- Advanced Options

The ping command has various options (switches) which you can see by typing

Ping My Network Connection

ping /? at the command prompt

So for a continuous ping we type

ping IP address or name -t

e.g.

ping google.com -t

Here is the result

IPv6 Addresses

If you have IPv6 configured on your system then you can also ping ipv6 addresses

on Windows networks you need to use ping -6 at the cmd prompt

Ping my network connection

example — ping -6 hostname or IP address

and on Linux systems use ping6

Ping My Wireless Network

example —ping6 -c 4 -I eth0 hostname or IP address

or

ping6 -c 4 IP address%eth0

Note: not using the Interface option may result in an Invalid Argument error

The screen shot below shows an IP4 and IP6 ping on linux

Common Questions and Answers

Q- What is the localhost?

A- On all operating systems localhost is the name given to your local machine and is resolved to the IP address 127.0.0.1.

Q- What is the Address 127.0.0.1?

A- This is known as the loopback address and is a special address assigned to your network interface.

Summary

The ping command is a networking utility available on all Operating systems that is used for troubleshooting on IP networks.

Related Articles and Resources

Yahoo Ping Test

[Total: 14 Average: 4.3]